\(\renewcommand\AA{\unicode{x212B}}\)

CubicSpline

Description

This function creates spline of order 3 using the set of points and interpolates the input between them taking into account the least-squares fit

First and second derivatives from the spline can be calculated by using the derivative1D function.

A CubicSpline is a polynomial function \(f(x)\) of order 3, defined between an interval \(a \leqslant x \leqslant b\). When using CubicSplines for interpolation or for fitting, we essentially chain BSplines of order 3 together so that each spline passes through the breakpoints in that interval.

A Cubic Spline is a specific case of BSpline that only uses polynomials of order 3 to define the spline functions.

Again, as with BSplines , there are certain conditions that must be fulfilled at each breakpoint such that the overall Spline is piecewise-smooth.

Example

To demonstrate these conditions we can set up a basic CubicSpline with 3 breakpoints:

Our CubicSpline will be defined as the following:

Breakpoints : \(x_0, x_1, x_2\)

\[\begin{split}C(x) = \begin{cases} f_1(x)& x_0 \leq x \leq x_1 \\ f_2(x)& x_1 \leq x \leq x_2 \\ \end{cases}\end{split}\]

Our piecewise functions can be written as \(f_1(x) = c_0x^3 + c_1x^2 + c_2x + c_3\) and \(f_2(x) = c_4x^3 + c_5x^2 + c_6x + c_7\)

To make our CubicSpline piecewise-smooth we must ensure that these conditions are satisfied:

\[\begin{split}f_1(x_0) = y_0\\ f_2(x_2) = y_2\\ \frac{df_1}{dx}(x_1) = \frac{df_2}{dx}(x_1)\\ \frac{d^2 f_1}{dx^2}(x_1) = \frac{d^2 f_2}{dx^2}(x_1)\\\end{split}\]

This point of smoothness is represented by the red circle in the graph below of our CubicSpline function \(C(x)\)

quadratic example of BSpline

CubicSplines and Fitting

Fitting using a CubicSpline fit function is different to interpolating with a CubicSpline as it requires the number of breakpoints to be less than the number of data points. This allows the CubicSpline to fit as close as possible to the dataset using a least-squares fit instead of passing through all data points as with interpolation. The fitted curve will pass through the breakpoints however it may not pass through all of the data points in the set.

A example of fitting with a CubicSpline has been provided below, with the breakpoints highlighted in green. The original data plot is in black and our fitted CubicSpline with four breakpoints is in red.

fitting example using BSplines

Attributes (non-fitting parameters)

Name Type Default Description
n Integer 3 Number of breakpoints in Spline
x0 Double - Position of first exterior breakpoint
x1 Double - Position of the interior breakpoint
x2 Double - Position of the last exterior breakpoint

Properties (fitting parameters)

Name Default Description
y0 0.0  
y1 0.0  
y2 0.0  

Even though the number of fitting parameters is set to 3 by default, this number is based off \(N + K - 2\). Where \(N\) is the number of breakpoints in the fit, \(K\) is the order of the spline (stays as 3 for the cubic spline case) and the \(-2\) accounts for our two exterior breakpoints \(x_0, x_n\). Increasing the number of breakpoints in your fit will increase the number of fitting parameters by the same amount.

Categories: FitFunctions | Background

Source

C++ header: CubicSpline.h

C++ source: CubicSpline.cpp